| BLUESIL ADD 10086 | Elkem Silicones | BLUESIL ADD 10086 is a polydimethylsiloxane gum in solvent solution especially developed to obtain hammer effects in combination with thixotropic polyurethane bases. It is also suitable for use with classical, polyurethane bases, thixotropic alkyd paints ...展开 BLUESIL ADD 10086 is a polydimethylsiloxane gum in solvent solution especially developed to obtain hammer effects in combination with thixotropic polyurethane bases. It is also suitable for use with classical, polyurethane bases, thixotropic alkyd paints and silicone binders. 收起 | |
| BLUESIL ADD 11013 | Elkem Silicones | BLUESIL ADD 11013 is a polyether-modified polydimethylsiloxane for use in solventless paints and varnishes, and in water-based paints and inks. | |
| BLUESIL BP 9200 | Elkem Silicones | BLUESIL BP 9200 is a solventless alkylpolysiloxane oligomer designed to enhance durability of construction materials as formed hard adhesion repellency layer through deep penetration. | |
| BLUESIL BP 9300 | Elkem Silicones | BLUESIL BP 9300 is a solventless alkylpolysiloxane oligomer designed to enhance durability of construction materials as formed hard adhesion repellency layer through deep penetration. | |
| BLUESIL BP 9705 | Elkem Silicones | BLUESIL BP 9705 is a non ionic, APEO free, polyorganosiloxane aqueous emulsion, to be used as a water repellent additive in various formulations for building materials. | |
| BLUESIL BP 9710 | Elkem Silicones | BLUESIL BP 9710 is an emulsion with an alkylpolysiloxane oligomer base designed to protect surfaces against moisture. This waterproofing system respects the environment since it is entirely formulated in a water base, it is free of any organic solvent and...展开 BLUESIL BP 9710 is an emulsion with an alkylpolysiloxane oligomer base designed to protect surfaces against moisture. This waterproofing system respects the environment since it is entirely formulated in a water base, it is free of any organic solvent and it does not contain ecotoxic surfactant. After it has dried on the surface, BLUESIL BP 9710 repels water and allows walls to breathe. Experience acquired over more than 40 years shows that silicone water repellents are a good answer to humidity problems in construction materials, particularly when for esthetical reasons the natural aspect of the material should be preserved. BLUESIL BP 9710 has been awarded a test certificate by CSTC (Centre Scientifique et Technique de - ): ref HD-340/133-151 on the 2006.02.20. 收起 | |
| BLUESIL BP 9800 | Elkem Silicones | BLUESIL BP 9800 is an aqueous APE-free polymethylsiloxane resin emulsion. This emulsion is designed for use in facade coatings, to optimise the balance between water repellency and water vapour permeability. | |
| BLUESIL BP 9821 | Elkem Silicones | BLUESIL BP 9821 is an aqueous APE-free polymethylsiloxane resin emulsion with low VOC content. This emulsion is designed for use in facade coatings, to optimise the balance between water repellency and water vapour permeability. | |
| BLUESIL BP 9878 | Elkem Silicones | BLUESIL BP 9878 is an aqueous polymethylsiloxane resin emulsion.This emulsion provides two fundamental properties of the silicone technology to the paint film: water repellency and permeability to water vapour. | |
| BLUESIL BP 9900 | Elkem Silicones | BLUESIL BP 9900 is a non ionic, APEO free, polyorganosiloxane aqueous emulsion, to be used as a water repellent additive for building materials. | |
| BLUESIL BP 9920 | Elkem Silicones | BLUESIL BP 9920is anon-ionic, APEO free, polyorganosiloxane aqueous emulsion, to be used as a water repellent additive in various formulations for building materials. | |
| BLUESIL EMUL 1803 | Elkem Silicones | BLUESIL EMUL 1803 is a non-ionic silicone emulsion containing silicone oil and resin. This emulsion is intended for mould-release of cast polyurethane elastomers. | |
| BLUESIL EMUL 269 | Elkem Silicones | BLUESIL EMUL 269 is an aqueous emulsion of an hydrogeno polysiloxane. | |
| BLUESIL EMUL 284 | Elkem Silicones | BLUESIL EMUL 284 is a slightly ionic oil-in-water type emulsion of a high viscosity a/w-hydroxydimethylpolysiloxane fluid. BLUESIL EMUL 284 is characterised by its reactivity, its outstanding stability, its lubricating power and its fabric softening prop...展开 BLUESIL EMUL 284 is a slightly ionic oil-in-water type emulsion of a high viscosity a/w-hydroxydimethylpolysiloxane fluid. BLUESIL EMUL 284 is characterised by its reactivity, its outstanding stability, its lubricating power and its fabric softening properties (textile applications). 收起 | |
| BLUESIL EMUL 3500 | Elkem Silicones | BLUESIL EMUL 3500 is a general purpose; non-ionic oil in water silicone emulsion, of a high viscosity hydroxyl terminated polysiloxane. | |
| BLUESIL EMUL 35B | Elkem Silicones | BLUESIL EMUL 35B is an oil-in-water emulsion containing 35 % silicone oil, which is diluted for use, generally in a proportion of one part of BLUESIL EMUL 35B to 20 to 200 parts of water. Its characteristics are as follows:Practically no tendency to cream...展开 BLUESIL EMUL 35B is an oil-in-water emulsion containing 35 % silicone oil, which is diluted for use, generally in a proportion of one part of BLUESIL EMUL 35B to 20 to 200 parts of water. Its characteristics are as follows:Practically no tendency to cream, neither during storage nor in use.Perfect stability in contact with hard water or zinc (i.e. in galvanized metal containers).Excellent heat stability after dilution.Very good wetting power. 收起 | |
| BLUESIL EMUL 55 | Elkem Silicones | BLUESIL EMUL 55 is a non-ionic, silicone oil-based aqueous emulsion with 35 % active material. It is mainly used as a mould-stripping agent in foundries, and also has applications in the rubber and plastics industries. Moreover, it is one of the component...展开 BLUESIL EMUL 55 is a non-ionic, silicone oil-based aqueous emulsion with 35 % active material. It is mainly used as a mould-stripping agent in foundries, and also has applications in the rubber and plastics industries. Moreover, it is one of the component elements making up polishes and cleaners for artificial leather fabrics (PVC, PUR) and furniture polishes. 收起 | |
| BLUESIL EMUL 872 | Elkem Silicones | BLUESIL EMUL 872 is a slightly anionic aqueous emulsion with a 60% dry content, for general purposes. This is a concentrated version of BLUESIL EMUL E1P. | |
| BLUESIL EMUL E1P | Elkem Silicones | BLUESIL EMUL E1P is an oil in water emulsion containing 35 % of a silicone oil. It can be used in many industries. | |
| BLUESIL EMUL E1P U1 | Elkem Silicones | BLUESIL EMUL E1P U1 is a general purpose, non-ionic, aqueous silicone emulsion. | |
| BLUESIL EMULSION 2400 | Elkem Silicones | BLUESIL EMUL 2400 is a general purpose; non-ionic oil in water silicone emulsion of a methyl-hydrogen polysiloxane. | |
| BLUESIL FLD 21625 | Elkem Silicones | BLUESIL FLD 21625is anα/ω-epoxy functionalised polydimethylsiloxane fluid. | |
| BLUESIL FLD 45 | Elkem Silicones | BLUESIL FLD 45 is a low viscosity dimethylpolysiloxane oil used to prevent floating and flooding and improve leveling of air-drying paints. | |
| BLUESIL FLD 47V1 000 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V100 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V350 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V50 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL FLD 47V500 | Elkem Silicones | BLUESIL FLD 47 V 50 to 47 V 1000 are straight chained polydimethylsiloxanic fluids. | |
| BLUESIL PI 2074 | Elkem Silicones | BLUESIL PI 2074 is a cationic photoinitiator for use with epoxy resins, vinyl ethers or any other type of oligomer which polymerises cationically. It is also suited to the formulation of hybrid radical / cationic systems. | |
| BLUESIL RES 6405 | Elkem Silicones | BLUESIL RES 6405 is a 50% solids methylphenylsilicone resin in Toluene (6405) or Xylene solution (6405X). This resin is ideal for the formulation of heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6405X | Elkem Silicones | BLUESIL RES 6405X is a 50% solids methylphenylsilicone resin in Toluene (6405) or Xylene solution (6405X). This resin is ideal for the formulation of heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6406XM | Elkem Silicones | BLUESIL RES 6406XM is a 60% solids methylphenylsilicone resin in Xylene solution. This resin is designed to formulate heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6407 | Elkem Silicones | BLUESIL RES 6407 is a 70% solids methylphenylsilicone resin in Toluene solution. This resin is designed to formulate heat resistant coatings for industrial applications with improved weatherability. | |
| BLUESIL RES 6482X | Elkem Silicones | BLUESIL RES 6482X is a reactive silicone resin which was developed for use in the manufacture of decorative medium temperature paints. Currently this resin is mainly used for the manufacture of air drying, temperature resistant silicone alkyd paints. It i...展开 BLUESIL RES 6482X is a reactive silicone resin which was developed for use in the manufacture of decorative medium temperature paints. Currently this resin is mainly used for the manufacture of air drying, temperature resistant silicone alkyd paints. It is also more compatible than other silicones with urea-formaldehyde, melamine-formaldehyde, epoxy, polyurethane and acrylic resins. Another use is as an additive for epoxy paints. It also improves weathering resistance. 收起 | |
| BLUESIL SP 3300 | Elkem Silicones | BLUESIL SP 3300 is a non hydrolysable silicone polyether copolymer. | |
| BLUESIL SP 3300 | Elkem Silicones | BLUESIL SP 3300 is a non hydrolysable silicone polyether copolymer. | |
| BLUESIL SP 3303 | Elkem Silicones | BLUESIL SP 3303 is a polyether modified polysiloxane. | |
| BLUESIL SP 3303 | Elkem Silicones | BLUESIL SP 3303 is a polyether modified polysiloxane. | |
| BLUESIL SP 3307 | Elkem Silicones | BLUESIL SP 3307 is a polyether modified polysiloxane. | |
| BLUESIL SP 3307 | Elkem Silicones | BLUESIL SP 3307 is a polyether modified polysiloxane. | |
| BLUESIL SP 3309 | Elkem Silicones | BLUESIL SP 3309 is a polyether modified trisiloxane. | |
| BLUESIL TCS 7001 | Elkem Silicones | BLUESIL TCS 7001 is an alkyl polysiloxane solution in solvent phase specifically developed for the waterproofing of fabrics and leathers exposed to difficult weather conditions by spraying or impregnating. | |
| CAF 2534 | Elkem Silicones | CAF 2534 is a one component silicone rubber that cures when in contact with air humidity. It is intended for use as a formulation base for the development of tie-coats in the fouling release treatment of boat hulls. | |
| ExBar™ 200 | Excalibar Minerals LLC | ExBar™ 200 is a raw mineral material that is manufactured from natural barium sulfate ore. This product is used in many different applications such as paints, adhesives and sealants. It has a median particle size of 15.0u and an oil absorption of 9. | |
| ExBar™ 325 | Excalibar Minerals LLC | ExBar™ 325 is a raw mineral material that is manufactured from natural barium sulfate ore. This product is used in many different applications such as paints, adhesives and sealants. It has a median particle size of 10.0u and an oil absorption of 10. | |
| ExBar™ 400 | Excalibar Minerals LLC | ExBar™ 400 is a raw mineral material that is manufactured from natural barium sulfate ore. This product is used in many different applications such as paints, adhesives and sealants. It has a median particle size of 8.0u and an oil absorption of 12. | |
| ExBar™ W 1 | Excalibar Minerals LLC | ExBar™ W 1 is manufactured using the highest quality white, natural barium sulfate ore. This product is often used in marine coatings, paints, powder coatings, adhesives, sealants, and many other applications where color, purity and particle size are prin...展开 ExBar™ W 1 is manufactured using the highest quality white, natural barium sulfate ore. This product is often used in marine coatings, paints, powder coatings, adhesives, sealants, and many other applications where color, purity and particle size are principle concerns. It has a median particle size of 1u and an oil absorption of 15. 收起 | |
| ExBar™ W 2 | Excalibar Minerals LLC | ExBar™ W 2 is manufactured using the highest quality white, natural barium sulfate ore. This product is often used in marine coatings, paints, powder coatings, adhesives, sealants, and many other applications where color, purity and particle size are prin...展开 ExBar™ W 2 is manufactured using the highest quality white, natural barium sulfate ore. This product is often used in marine coatings, paints, powder coatings, adhesives, sealants, and many other applications where color, purity and particle size are principle concerns. It has a median particle size of 2u and an oil absorption of 13. 收起 | |
| ExBar™ W 3 | Excalibar Minerals LLC | ExBar™ W 3 is manufactured using the highest quality white, natural barium sulfate ore. This product is often used in marine coatings, paints, powder coatings, adhesives, sealants, and many other applications where color, purity and particle size are prin...展开 ExBar™ W 3 is manufactured using the highest quality white, natural barium sulfate ore. This product is often used in marine coatings, paints, powder coatings, adhesives, sealants, and many other applications where color, purity and particle size are principle concerns. It has a median particle size of 3u and an oil absorption of 13. 收起 | |
| ExBar™ W 325 | Excalibar Minerals LLC | ExBar™ W 325 is manufactured using the highest quality white, natural barium sulfate ore. This product is often used in marine coatings, paints, powder coatings, adhesives, sealants, and many other applications where color, purity and particle size are pr...展开 ExBar™ W 325 is manufactured using the highest quality white, natural barium sulfate ore. This product is often used in marine coatings, paints, powder coatings, adhesives, sealants, and many other applications where color, purity and particle size are principle concerns. 收起 | |
| ExBar™ W 4 | Excalibar Minerals LLC | ExBar™ W 4 is manufactured using the highest quality white, natural barium sulfate ore. This product is often used in marine coatings, paints, powder coatings, adhesives, sealants, and many other applications where color, purity and particle size are prin...展开 ExBar™ W 4 is manufactured using the highest quality white, natural barium sulfate ore. This product is often used in marine coatings, paints, powder coatings, adhesives, sealants, and many other applications where color, purity and particle size are principle concerns. It has a median particle size of 4u and an oil absorption of 12. 收起 | |
| ExBar™ W 400 | Excalibar Minerals LLC | ExBar™ W 400 is manufactured using the highest quality white, natural barium sulfate ore. This product is often used in marine coatings, paints, powder coatings, adhesives, sealants, and many other applications where color, purity and particle size are pr...展开 ExBar™ W 400 is manufactured using the highest quality white, natural barium sulfate ore. This product is often used in marine coatings, paints, powder coatings, adhesives, sealants, and many other applications where color, purity and particle size are principle concerns. It has a median particle size of 8u and an oil absorption of 10. 收起 | |
| ExCal® 100 | Excalibar Minerals LLC | ExCal® 100 is a calcium carbonate product that is processed from a high-purity stone. This product is primarily used in adhesives, sealants, and other applications. | |
| ExCal® 200 | Excalibar Minerals LLC | ExCal® 200 is a calcium carbonate product that is processed from a high-purity stone. This product is primarily used in adhesives, sealants, and other applications. | |
| ExCal® 325 | Excalibar Minerals LLC | ExCal® 325 is a calcium carbonate product that is processed from a high-purity stone. This product is primarily used in adhesives, sealants, and other applications. | |
| ExCal® 400 | Excalibar Minerals LLC | ExCal® 400 is a calcium carbonate product that is processed from a high-purity stone. This product is primarily used in adhesives, sealants, and other applications. | |
| ExCal® CW 100 | Excalibar Minerals LLC | ExCal® CW 100 is a calcium carbonate product that is processed from a high-purity ore. This product can be used for several different applications such as coatings, adhesives, sealants and many other specialty applications where color and binder demand ar...展开 ExCal® CW 100 is a calcium carbonate product that is processed from a high-purity ore. This product can be used for several different applications such as coatings, adhesives, sealants and many other specialty applications where color and binder demand are a standard. 收起 | |
| ExCal® CW 200 | Excalibar Minerals LLC | ExCal® CW 200 is a calcium carbonate product that is processed from a high-purity ore. This product can be used for several different applications such as coatings, adhesives, sealants and many other specialty applications where color and binder demand ar...展开 ExCal® CW 200 is a calcium carbonate product that is processed from a high-purity ore. This product can be used for several different applications such as coatings, adhesives, sealants and many other specialty applications where color and binder demand are a standard. 收起 | |
| ExCal® CW 325 | Excalibar Minerals LLC | ExCal® CW 325 is a calcium carbonate product that is processed from a high-purity ore. This product can be used for several different applications such as coatings, adhesives, sealants and many other specialty applications where color and binder demand ar...展开 ExCal® CW 325 is a calcium carbonate product that is processed from a high-purity ore. This product can be used for several different applications such as coatings, adhesives, sealants and many other specialty applications where color and binder demand are a standard. 收起 | |
| KLX 7997 | Nokxeller Quimica Ltda | KLX 7997 is a versatile polyether based aromatic isocyanate anionic dispersion for high tack formulations. It has a very soft and flexible film that can be used as a high initial and final bond strength and heat resistance. Typical applications are for mo...展开 KLX 7997 is a versatile polyether based aromatic isocyanate anionic dispersion for high tack formulations. It has a very soft and flexible film that can be used as a high initial and final bond strength and heat resistance. Typical applications are for modifying pressure sensitive textile & construction adhesives, neoprene, EVA and other plastic & leather primer applications. Once crosslinked shows outstanding water resistance. 收起 | |
| LYNDCOAT 15 RTU | Elkem Silicones | LYNDCOAT 15 RTU is a ready to use water-based coating designed for use in tire molds. It is a blend of polymers that cures at typical molding temperatures to form a clear, tough bond possessing excellent release and lubrication properties. Lyndcoat™ 15 RT...展开 LYNDCOAT 15 RTU is a ready to use water-based coating designed for use in tire molds. It is a blend of polymers that cures at typical molding temperatures to form a clear, tough bond possessing excellent release and lubrication properties. Lyndcoat™ 15 RTU also helps keep molds and vents clean, reducing defects and downtime. Lyndcoat™ 15 RTU typically is durable through multiple production cycles. The need for reapplication is dependent on factors such as the rubber compound, curing time, curing temperature, tread design and application technique. Lyndcoat™ 15 RTU is designed for processes requiring low viscosity mold lubricants. 收起 | |
| LYNDCOAT BR 1100 RTU | Elkem Silicones | LYNDCOAT BR1100 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1100 RTU replaces the c...展开 LYNDCOAT BR1100 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1100 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR1100 RTU does not contain aromatic or chlorinated solvents. It is easy to use and is recommended for a single release application. It can be brushed, swabbed, or sprayed onto the rubber surface. Lyndcoat™ BR1100 RTU is of high viscosity and does not contain mica. For maximum release and bladder life, the use of a durable bladder pre-treatment such as Lyndcoat™ BR2101 RTU is highly recommended. 收起 | |
| LYNDCOAT BR 1102 | Elkem Silicones | LYNDCOAT BR1102 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1102 RTU replaces the c...展开 LYNDCOAT BR1102 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR1102 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR1102 RTU does not contain aromatic or chlorinated solvents. It is easy to use and is recommended for a single release application. It can be brushed, swabbed, or sprayed onto the rubber surface. Lyndcoat™ BR1102 RTU is of medium viscosity and does not contain mica. 收起 | |
| LYNDCOAT BR 1103 RTU | Elkem Silicones | LYNDCOAT BR1103 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR1103 RTU replaces the c...展开 LYNDCOAT BR1103 RTU is a ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR1103 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. LYNDCOAT® BR1103 RTU does not contain aromatic or chlorinated solvents. It is easy to use and is recommended for a single release application. It can be brushed, swabbed, or sprayed onto the rubber surface. LYNDCOAT® BR1103 RTU is of high viscosity and does not contain mica. For maximum release and bladder life, the use of a durable bladder pre-treatment such as LYNDCOAT® BR2201 RTU is highly recommended. 收起 | |
| LYNDCOAT BR 1110 RTU | Elkem Silicones | LYNDCOAT is a ready to use, silicone based, high mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coating that offers ...展开 LYNDCOAT is a ready to use, silicone based, high mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coating that offers excellent release properties and lubricity. In addition, the product promotes air bleed and reduces defects caused by trapped air and buckled bladders. LYNDCOAT BR 1110 RTU replaces conventional lining cements and solvent based band ply lubricants, eliminating the flammability and toxicityproblems associated with these kinds of products. LYNDCOAT BR 1110 RTU is easy to use and is recommended for a single release application. It can be brushed, swabbed or sprayed onto the rubber surface. For maximum release and bladder life, the use of a durable bladder pre-treatment, such as LYNDCOAT BR 2101 RTU, is highly recommended. 收起 | |
| LYNDCOAT BR 1211 | Elkem Silicones | LYNDCOAT BR1211 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It was designed for improved bladder protection, a clean operation and reduced press downtim...展开 LYNDCOAT BR1211 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It was designed for improved bladder protection, a clean operation and reduced press downtimes. Applied on the inside of the green tire, or directly on the bladder, it insures excellent release, slip and air bleed performance. 收起 | |
| LYNDCOAT BR 1214 | Elkem Silicones | LYNDCOAT BR 1214 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It is particularly friction resistant and slip promoting. Applied on the inside of the green...展开 LYNDCOAT BR 1214 is a ready to use, water based band ply lubricant. It is part of the new generation reactive silicone emulsions allowing for low coating weights. It is particularly friction resistant and slip promoting. Applied on the inside of the green tire, or directly on the bladder, it insures excellent release, slip and air bleed performance. 收起 | |
| LYNDCOAT BR 1623 RTU | Elkem Silicones | LYNDCOAT BR 1623 RTU is a ready to use, silicone based, medium mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coatin...展开 LYNDCOAT BR 1623 RTU is a ready to use, silicone based, medium mica content release coating for butyl rubber bladders typically used in tire curing presses. It is an aqueous system that cures during the tire vulcanization process to a tightly bound coating that offers excellent release properties and lubricity. In addition, the product promotes air bleed and reduces defects caused by trapped air and buckled bladders. Lyndcoat BR 1623 RTU replaces conventional lining cements and solvent based band ply lubricants, eliminating the flammability and toxicityproblems associated with these kinds of products. Lyndcoat BR 1623 RTU is easy to use and is recommended for a single release application. It can be brushed, swabbed or sprayed onto the rubber surface. For maximum release and bladder life, the use of a durable bladder pre-treatment, such as Lyndcoat XR 3900 Primer, is highly recommended. 收起 | |
| LYNDCOAT BR 1812 | Elkem Silicones | LYNDCOAT BR 1812 is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR 1812 RTU replace...展开 LYNDCOAT BR 1812 is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR 1812 RTU replaces the conventional lining cements and solvent-based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR 1812 RTU does not contain aromatic or chlorinated solvents. It is easy to use and can be brushed, swabbed or sprayed onto the rubber surface, remaining effective through multiple curing cycles. The cycles between applications depend on application efficiency, curing time, curing temperature, tire construction and composition, and condition. Lyndcoat™ BR 1812 RTU is of low viscosity and does not contain mica. It has been shown to increase productivity, improve tire aesthetics and appearance, prolong bladder life, and reduce costs. 收起 | |
| LYNDCOAT BR 2100 RTU | Elkem Silicones | LYNDCOAT BR 2100 RTU is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures durable performance. | |
| LYNDCOAT BR 2104 | Elkem Silicones | LYNDCOAT BR 2104 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a long lasting multi release and slip performance. It was designed to...展开 LYNDCOAT BR 2104 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a long lasting multi release and slip performance. It was designed to reduce build up notably in the bead area. 收起 | |
| LYNDCOAT BR 2201 | Elkem Silicones | LYNDCOAT BR 2201 is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR 2201 replaces t...展开 LYNDCOAT BR 2201 is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. LYNDCOAT® BR 2201 replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. LYNDCOAT® BR 2201 does not contain aromatic or chlorinated solvents. It is easy to use and can be brushed, swabbed, or sprayed onto the rubber surface, remaining effective through multiple curing cycles. The cycles between applications depend on application efficiency, curing time, curing temperature, tire construction and composition, and condition. LYNDCOAT® BR 2201 is of high viscosity and does not contain mica. It has been shown to increase productivity, improve tire aesthetics and appearance, prolong bladder life, and reduce costs. 收起 | |
| LYNDCOAT BR 2204 A1 | Elkem Silicones | LYNDCOAT BR 2204 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a multi release and slip performance. It was designed to reduce build...展开 LYNDCOAT BR 2204 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a multi release and slip performance. It was designed to reduce build up notably in the bead area. 收起 | |
| LYNDCOAT BR 2204 E4 | Elkem Silicones | LYNDCOAT BR 2204 E4 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a multi release and slip performance. It was designed to reduce b...展开 LYNDCOAT BR 2204 E4 is a solvent free, silicone based, ready to use, inside paint and bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it insures a multi release and slip performance. It was designed to reduce build up notably in the bead area. 收起 | |
| LYNDCOAT BR 2511 RTU | Elkem Silicones | LYNDCOAT BR2511 RTU is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it combines long lasting multi release with excellent slip and exceptional air bleed performan...展开 LYNDCOAT BR2511 RTU is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it combines long lasting multi release with excellent slip and exceptional air bleed performance. 收起 | |
| LYNDCOAT BR 2512 | Elkem Silicones | LYNDCOAT BR2512 is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it combines particularly long lasting multi release and slip with exceptional air bleed performanc...展开 LYNDCOAT BR2512 is a solvent free, silicone based, ready to use, bladder release agent. Applied on the inside of the green tire, or directly on the bladder, it combines particularly long lasting multi release and slip with exceptional air bleed performance. 收起 | |
| LYNDCOAT BR 601 RTU | Elkem Silicones | LYNDCOAT BR-601 RTU is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR-601 RTU rep...展开 LYNDCOAT BR-601 RTU is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR-601 RTU replaces the conventional lining cements and solvent-based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR-601 RTU does not contain any solvents. It is easy to use and can be brushed, swabbed or sprayed onto the rubber surface, remaining effective through multiple curing cycles. The cycles between applications depend on application efficiency, curing time, curing temperature, tire construction and composition, and condition. Lyndcoat™ BR-601 RTU is of medium viscosity and does not contain mica. It has been shown to increase productivity, improve tire aesthetics and appearance, prolong bladder life, and reduce costs. 收起 | |
| LYNDCOAT BR 790 RTU | Elkem Silicones | LYNDCOAT BR 790 RTU is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR-790 RTU rep...展开 LYNDCOAT BR 790 RTU is a durable, ready to use silicone-based bladder release coating designed for butyl rubber bladders typically used in tire curing presses. It is a white aqueous emulsion that promotes excellent slip/release. Lyndcoat™ BR-790 RTU replaces the conventional lining cements and solvent based band ply lubricants, eliminating the problems of flammability, toxicity, and dusty/flaky residues. Lyndcoat™ BR-790 RTU does not contain any solvents. It is easy to use and can be brushed, swabbed or sprayed onto the rubber surface, remaining effective through multiple curing cycles. The cycles between applications depend on application efficiency, curing time, curing temperature, tire construction and composition, and condition. Lyndcoat™ BR-790 RTU is of low viscosity and does not contain mica. It has been shown to increase productivity, improve tire aesthetics and appearance, prolong bladder life, and reduce costs. 收起 | |
| LYNDCOAT MR 5100 RTU | Elkem Silicones | LYNDCOAT MR 5100 RTU is a ready to use, solvent free, water based coating designed for use in tire moulds. It is a blend of polymers that cure at typical molding temperatures to form a clear, tough, coating with a strong bond to the metal mould, possessin...展开 LYNDCOAT MR 5100 RTU is a ready to use, solvent free, water based coating designed for use in tire moulds. It is a blend of polymers that cure at typical molding temperatures to form a clear, tough, coating with a strong bond to the metal mould, possessing excellent release and lubrication properties towards rubber. LYNDCOAT MR 5100 RTU helps keep moulds and vents clean, which reduces defects and downtime. LYNDCOAT MR 5100 RTU is durable through multiple production cycles. The need for reapplication is dependent on factors such as: the rubber compound, tread design, curing time, curing temperature, application technique and press type. LYNDCOAT MR 5100 RTU is designed for processes requiring low viscosity mould lubricants. 收起 | |
| NKX 144 | Nokxeller Quimica Ltda | NKX 144 is a small particle size high gloss PU polyesther aliphatic topcoat. It forms a transparent film of medium hardness suitable as a final varnish or topcoat where high gloss, abrasion resistance and clarity are required. When crosslinked, presents e...展开 NKX 144 is a small particle size high gloss PU polyesther aliphatic topcoat. It forms a transparent film of medium hardness suitable as a final varnish or topcoat where high gloss, abrasion resistance and clarity are required. When crosslinked, presents excellent weatherability. It is ideal for use as a topcoat for leather finish and PVC, indoor paints formulation, etc. 收起 | |
| NKX 176 | Nokxeller Quimica Ltda | NKX 176 is a soft and elastic PUD with outstanding film-forming properties. NKX 176 is a NON IONIC VOC free soft non tacky and elastic PUD with outstanding film-forming properties. It can be used as a universal coating resin for textile due to its varied ...展开 NKX 176 is a soft and elastic PUD with outstanding film-forming properties. NKX 176 is a NON IONIC VOC free soft non tacky and elastic PUD with outstanding film-forming properties. It can be used as a universal coating resin for textile due to its varied possibility of uses. NKX 176 has a flexible and soft but non-tacky handle. It has varied applications especially in textile finishes where body handle, durability are required. It is ideal for use as a print binder and as an universal coating resin in textile applications, garment leather finish, and coatings for digital printing in fabrics. 收起 | |
| NKX 183 | Nokxeller Quimica Ltda | NKX 180 based resin, with higher concentration.Multipurpose resin of extreme adhesion, outstanding toughness and abrasion resistance suitable for coatings for the following substrates: plastic, synthetic fabric, metal, shoe finish, etc. Due to its high cr...展开 NKX 180 based resin, with higher concentration.Multipurpose resin of extreme adhesion, outstanding toughness and abrasion resistance suitable for coatings for the following substrates: plastic, synthetic fabric, metal, shoe finish, etc. Due to its high crystalline segment concentration the polymer presents itself tough, yet flexible and resistant. 收起 | |
| NKX 201 NMP-Free | Nokxeller Quimica Ltda | NKX 201 NMP-Free shows excellent chemical, weathering and abrasion resistance due to higher resistance of this kind of polyol. NKX 201 presents wide use possibilities considering its high gloss and transparency properties as in synthetic substrates, as hi...展开 NKX 201 NMP-Free shows excellent chemical, weathering and abrasion resistance due to higher resistance of this kind of polyol. NKX 201 presents wide use possibilities considering its high gloss and transparency properties as in synthetic substrates, as high gloss topcoats in leather finish, wood flooring or print screen putties, metallic applications. 收起 | |
| NKX 240 | Nokxeller Quimica Ltda | NKX 240 is a multipurpose resin of exceptional properties was developed to serve a wide range of applications for flexible and rigid substrates. NKX 240 shows up a clear film with good gloss retention and presents high adhesion and heat resistance. | |
| NKX 245 | Nokxeller Quimica Ltda | NKX-245 is a modified polyester type suitable for glossy aqueous coatings as wood flooring. NKX 245 has a very hard film providing high abrasion resistance, and adhesion and can be easily formulated along with other components such as acrylic resins, pigm...展开 NKX-245 is a modified polyester type suitable for glossy aqueous coatings as wood flooring. NKX 245 has a very hard film providing high abrasion resistance, and adhesion and can be easily formulated along with other components such as acrylic resins, pigment dispersions, fillers, thickeners, etc. 收起 | |
| NKX 250 | Nokxeller Quimica Ltda | NKX-250 is a very hard PUD polyester type adequate for clear or pigmented waterbased topcoat for rigid substrates specially furniture, metal or hard synthetic substrates. Its hard, transparent and glossy film provides good abrasion resistance, adhesion an...展开 NKX-250 is a very hard PUD polyester type adequate for clear or pigmented waterbased topcoat for rigid substrates specially furniture, metal or hard synthetic substrates. Its hard, transparent and glossy film provides good abrasion resistance, adhesion and gloss. 收起 | |
| NKX 274 | Nokxeller Quimica Ltda | NKX 274 is a high solid small particle size resin with excellent chemical resistance. It is adequate for varied market segments wherever is necessary to replace a solventborne for a waterborne paint. Typical uses in metal, soles, PVC, other synthetic subs...展开 NKX 274 is a high solid small particle size resin with excellent chemical resistance. It is adequate for varied market segments wherever is necessary to replace a solventborne for a waterborne paint. Typical uses in metal, soles, PVC, other synthetic substrate paint compositions wherever high gloss, good adhesions and chemical resistance are necessary. 收起 | |
| NKX 279 | Nokxeller Quimica Ltda | NKX 279 is a fine particle size resin and developed to formulate water topcoats of high adhesion and very good chemical resistance. Typical end use applications include top coatings for rigid and flexible substrates including wood, paper, metallic surface...展开 NKX 279 is a fine particle size resin and developed to formulate water topcoats of high adhesion and very good chemical resistance. Typical end use applications include top coatings for rigid and flexible substrates including wood, paper, metallic surface , plastics and especially PVC and other synthetic laminates.NKX 279 is high performance water based coating and can replace traditional solvent based coatings in wide applications possibilities. 收起 | |
| P5016 (50:50) | Huangshan Huizhou Jiajie Chemical Co., Ltd. | P5016 (50:50) is a carboxyl-saturated polyester resin that are yellow to clear flakes. This product can be used in combination with epoxy resin, in an equal mixture, to produce hybrid powder coatings that are receptive to the addition of pigments. | |
| P5016-1 (50:50) | Huangshan Huizhou Jiajie Chemical Co., Ltd. | P5016-1 (50:50) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin, in an equal mixture, to produce hybrid powder coatings that are receptive to the addition of pi...展开 P5016-1 (50:50) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin, in an equal mixture, to produce hybrid powder coatings that are receptive to the addition of pigments. 收起 | |
| P5016-2 (50:50) | Huangshan Huizhou Jiajie Chemical Co., Ltd. | P5016-2 (50:50) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin, in an equal mixture, to produce hybrid powder coatings that are receptive to the addition of pi...展开 P5016-2 (50:50) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin, in an equal mixture, to produce hybrid powder coatings that are receptive to the addition of pigments. 收起 | |
| P5016-3 (50:50) | Huangshan Huizhou Jiajie Chemical Co., Ltd. | P5016-3 (50:50) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin, in an equal mixture, to produce hybrid powder coatings that are receptive to the addition of pi...展开 P5016-3 (50:50) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin, in an equal mixture, to produce hybrid powder coatings that are receptive to the addition of pigments. 收起 | |
| P5016-4 (50:50) | Huangshan Huizhou Jiajie Chemical Co., Ltd. | P5016-4 (50:50) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin, in an equal mixture, to produce hybrid powder coatings that are receptive to the addition of pi...展开 P5016-4 (50:50) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin, in an equal mixture, to produce hybrid powder coatings that are receptive to the addition of pigments. 收起 | |
| P6016 (60:40) | Huangshan Huizhou Jiajie Chemical Co., Ltd. | P6016 (60:40) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin to produce hybrid powder coatings that are receptive to the addition of pigments. It can provide h...展开 P6016 (60:40) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin to produce hybrid powder coatings that are receptive to the addition of pigments. It can provide high gloss, good flow effect, excellent yellowing resistance, and marked durability to high-quality coatings. 收起 | |
| P6016-1 (60:40) | Huangshan Huizhou Jiajie Chemical Co., Ltd. | P6016-1 (60:40) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin to produce hybrid powder coatings that are receptive to the addition of pigments. It can provide...展开 P6016-1 (60:40) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin to produce hybrid powder coatings that are receptive to the addition of pigments. It can provide high gloss, good flow effect, excellent yellowing resistance, and marked durability to high-quality coatings. 收起 | |
| P6016-2 (60:40) | Huangshan Huizhou Jiajie Chemical Co., Ltd. | P6016-2 (60:40) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin to produce hybrid powder coatings that are receptive to the addition of pigments. It can provide...展开 P6016-2 (60:40) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin to produce hybrid powder coatings that are receptive to the addition of pigments. It can provide high gloss, good flow effect, excellent yellowing resistance, and marked durability to medium-level quality coatings. 收起 | |
| P6016-3 (60:40) | Huangshan Huizhou Jiajie Chemical Co., Ltd. | P6016-3 (60:40) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin to produce hybrid powder coatings that are receptive to the addition of pigments. It can provide...展开 P6016-3 (60:40) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin to produce hybrid powder coatings that are receptive to the addition of pigments. It can provide high gloss, good flow effect, excellent yellowing resistance, and marked durability to medium-level quality coatings. 收起 | |
| P6016-4 (60:40) | Huangshan Huizhou Jiajie Chemical Co., Ltd. | P6016-4 (60:40) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin to produce hybrid powder coatings that are receptive to the addition of pigments. It can provide...展开 P6016-4 (60:40) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resin to produce hybrid powder coatings that are receptive to the addition of pigments. It can provide high gloss, good flow effect, excellent yellowing resistance, and marked durability to medium-level quality coatings. 收起 | |
| P7013H (70:30) | Huangshan Huizhou Jiajie Chemical Co., Ltd. | P7013H (70:30) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resins to produce hybrid powder coatings. It can provide high gloss, good flow effect, excellent yellow...展开 P7013H (70:30) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resins to produce hybrid powder coatings. It can provide high gloss, good flow effect, excellent yellowing resistance, and marked durability to high gloss powder coatings. 收起 | |
| P7013H-1 (70:30) | Huangshan Huizhou Jiajie Chemical Co., Ltd. | P7013H-1 (70:30) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resins to produce hybrid powder coatings. It can provide high gloss, good flow effect, excellent yell...展开 P7013H-1 (70:30) is a carboxyl-saturated polyester resin that appears as clear to light yellow flakes. This product can be used in combination with epoxy resins to produce hybrid powder coatings. It can provide high gloss, good flow effect, excellent yellowing resistance, and marked durability to high gloss powder coatings. 收起 |
